How to buy a classic motorcycle in SA?

'There are a few things you need to consider,’ writes bike guru Dries Van der Walt.

Top family cars in SA

Wheels24's Janine Van der Post has gone from a 'SpeedQueen' to a supermom. Check out her list of top family cars.

Close-up on Renault's turbo F1 engine

2014-01-24 12:25

DYNAMITE COMES IN SMALL PACKAGES: Renault's new 1.6-litre F1 V6 turbo engine is said to be more powerful and efficient than the former V8. Image: Renault

PARIS, France - Formula 1 engine manufacturer Renault has released images of its eagerly awaited V6 turbo. Renault is engine supplier to five teams in F1 and the images the automaker released depict a much smaller power unit equipped with an energy recovery system.

Wheels24 has compiled a gallery of the V6 turbo engine.

According to Renault: "Energy efficiency will reach levels never seen in the sport before, with two types of energy propelling the cars."

The internal combustion engine will produce power through consumption of traditional carbon-based fuel, while electrical energy will be harvested from exhaust and braking by two motor generator units.

The two systems will work in harmony, with teams and drivers balancing the use of the two types of energy throughout the race.


The advent of this new technology means that the word ‘engine’ is no longer sufficient, instead the sport will refer to ‘Power Units.’

Renault's says its Energy F1-2014 Power Unit was designed and developed at its Viry-Châtillon headquarters in France.

President of Renault Sport F1, Jean-Michel Jalinier, said: "Grand Prix racing is a pioneering sport, representing the pinnacle of human endeavour and technological innovation.

"From the rear-mounted engines of the 1930's to the ground effect of the 1980's, F1 technology has always been years ahead of its time.

Jalinier added: With cutting-edge energy systems and highly advanced turbocharged combustion engines, in 2014 F1 remains true to its DNA. We are absolutely at the vanguard of power train technology this year."


In short:
V6 is shorthand for an internal combustion engine with its cylinders arranged in two banks of three cylinders arranged in a ‘V’ configuration over a common crankshaft. The Renault Energy F1 V6 has a displacement of 1.6 litres and will produce 447kW.

The challenge:
Contrary to popular belief, the ICE is not the easiest part of the power unit to design as the architecture is very different to the incumbent V8s.

Due to the turbocharger, the pressures within the combustion chamber are enormous – almost twice as much as the V8. The crankshaft and pistons will be subject to massive stresses and the pressure within the combustion chamber may rise to 200bar, or over 200 times ambient pressure.

One to watch:
The pressure generated by the turbocharger may produce a ‘knocking’ within the combustion chamber that is very difficult to control or predict. Should this destructive phenomenon occur, the engine will be destroyed immediately.

In short:
All Power Units must have direct fuel injection (DI), where fuel is sprayed directly into the combustion chamber rather than into the inlet port upstream of the inlet valves. The fuel-air mixture is formed within the cylinder, so great precision is required in metering and directing the fuel from the injector nozzle. This is a key sub-system at the heart of the fuel efficiency and power delivery of the power unit.

The challenge:
One of the central design choices of the ICE was whether to make the DI top mounted (where the fuel is sprayed at the top of the combustion chamber close to the spark plug) or side mounted (lower down the chamber).

One to watch:
The option still remains to cut cylinders to improve efficiency and driveability through corners.

In short:
A turbocharger uses exhaust gas energy to increase the density (compress) of the engine intake air and therefore produce more power. Similar to the principle employed on road cars, the turbocharger allows a smaller engine to make much more power than its size would normally permit.

The exhaust energy is converted to mechanical shaft power by an exhaust turbine. The mechanical power from the turbine is then used to drive the compressor, and also the MGU-H (see below).

The challenge:
At its fastest point the turbocharger is rotating at 100 000rpm, more than 1500 times per second, so the pressures and temperatures generated will be enormous. Some of the energy recovered from the exhaust will be passed on to the MGU-H and converted to electrical energy that will be stored and can later be re-deployed to prevent the turbo slowing too much under braking.

One to watch:
As the turbocharger speed must vary to match the requirement of the engine, there may be a delay in torque response, known as turbo lag, when the driver gets on the throttle after a period of sustained braking. One of the great challenges of the new power unit is to reduce this to near zero to match the instant torque delivery of the V8 engines.

In short:
On conventional turbo engines, a wastegate is used in association with a turbocharger to control the high rotation speeds of the system. It is a control device that allows excess exhaust gas to by-pass the turbine and match the power produced by the turbine to that needed by the compressor to supply the air required by the engine.

On the Renault Energy F1, the turbo rotation speed is primarily controlled by the MGU-H (see below) however a wastegate is needed to keep full control in any circumstance (quick transient or MGU-H deactivation).

The challenge:
The wastegate is linked to the turbocharger but sits in a very crowded area of the car. The challenge is therefore to make it robust enough to withstand the enormous pressures while small enough to fit.

One to watch:
On a plane there are certain parts that are classified as critical if they fail. By this measure the wastegate is the same: if it fails the consequences will be very serious.

In short:
The MGU-K is connected to the crankshaft of the internal combustion engine. Under braking, the MGU-K operates as a generator, recovering some of the kinetic energy dissipated during braking. It converts this into electricity that can be deployed throughout the lap (limited to 120kW by the rules). Under acceleration, the MGU-K is powered from the Energy Store and/or from the MGU-H and acts as a motor to propel the car.

The challenge:
While in 2013 a failure of kers (kinetic energy recovery system) would cost about 0.3sec per lap at about half the races, the consequences of a MGU-K failure in 2014 would be far more serious, leaving the car propelled only by the internal combustion engine and effectively uncompetitive.

One to watch:
Thermal behaviour is a massive issue as the MGU-K will generate three times as much heat as the V8 KERS unit.

In short:
The MGU-H is connected to the turbocharger. Acting as a generator, it absorbs power from the turbine shaft to convert heat energy from the exhaust gases. The electrical energy can be either directed to the MGU-K or to the battery for storage for later use.

The MGU-H is also used to control the speed of the turbocharger to match the air requirement of the engine (eg. to slow it down in place of a wastegate or to accelerate it to compensate for turbo lag.)

The challenge:
The MGU-H produces alternating current but the battery is direct current so a highly complex converter is needed.

One to watch:
Very high rotational speeds are a challenge as the MGU-H is coupled to a turbocharger spinning at as much as 100 000rpm.

In short:
Heat and kinetic energy recovered can be consumed immediately or stored in a battery. The stored energy can be used to propel the car with the MGU-K or to accelerate the turbocharger with the MGU-H. Compared to 2013 kers, the ERS of the 2014 power unit will have twice the power (120kW vs 60kW) and the energy contributing to performance is 1o times greater.

The challenge:
The battery has a minimum weight of 20kg to power a motor that produces 120kW. Each 1kg feeds 6kw (a huge power-to-weight ratio), which will produce large electromagnetic forces.

One to watch:
The electromagnetic forces can affect the accuracy of sensors, which are particularly sensitive. Balancing the forces is like trying to carry a house of cards in a storm – a delicate and risky operation.

In short:
The intercooler is used to cool the engine intake air after it has been compressed by the turbocharger.

The challenge:
The presence of an intercooler (absent in the non-turbo V8 engines), coupled with the increase in power from the energy recovery systems, creates a complicated integration process since the total surface area of the cooling system and radiators has increased significantly over that of 2013.

One to watch:
Integration of the intercooler and other radiators is vital but effective cooling without incorporating giant radiators is a major challenge and key performance factor.

Inside Wheels24

A 'Butler' drinks from a shoe, Alonso gets racy... 5 top moments from the US GP

From Lewis Hamilton dominating in Texas to actor Gerard Butler drinking from a stinking race shoe.. the 2016 United States GP proved to be one of the best races of the season. These top moments made it worth watching...

There are new stories on the homepage. Click here to see them.